Translation of "Charge acceptance" in German

In the photoconductive system, the acceptors produce a reduction in the residual discharge and also an improved constancy of the cyclic parameters without impairment of the other good electrophotographic properties, such as photosensitivity, charge acceptance, dark decay, preexposure sensitivity, etc.

Polymer films from this phase have the disadvantage of reduced charge acceptance and release at higher currents, so that their higher surface-specific capacity has only limited usefulness.

If an electrophotographic photoreceptor which has been sensitized with soluble dyes of the type mentioned is accidentally exposed to light before the copying process, then after charging by means of a corona a highly reduced charge acceptance is observed in the previously exposed areas.

The electrophotographic recording material produced in this way had a high charge acceptance (see Table 1) and excellent spectral sensitivity in the range from 400 to 800 nm with positive charging.

But due to the high proportion of zinc oxide, layers of this kind show a relatively low mechanical stability and a relatively poor charge acceptance.

Because of the high proportion of photoconductor in such layers, direct application to metals, such as copper or iron, often leads to contamination of the layer or surface and, thus, to a considerably reduced charge acceptance which severely hampers practical use.

It is another object of the present invention to provide an electrophotographic recording material which can be easily and inexpensively produced, which shows a high photosensitivity and high voltage contrasts, at a good negative charge acceptance, and which retains low residual potentials after exposure.

Pigment concentrations which are too high lead to a deterioration of charge acceptance and, consequently, a pigment content of about 50 percent by weight is regarded as an approximate upper limit.

In order to ensure good charge acceptance of the photoconductive layer, the concentration of the p-type conducting photoconductor should not exceed 20 percent by weight, based on the layer weight.

In order to ensure sufficient charge acceptance, the layer weight should not be below about 3 g/m2.

The most critical evaluation metric in RSRT 's analysis was battery-cell testing, which included micro-hybrid test ("MHT"), dynamic charge acceptance ("DCA"), Capacity (C20 and C), and breakdown analysis.

Dynamic Charge Acceptance or DCA is the ability of a battery to accept instantaneous energy during charging.

This innovation places new demands on car batteries, particularly with respect to partial state of charge management and charge acceptance.

The durability studies on batteries which comprise the inventive expander in their material for the negative electrode showed that improved SOC (state of charge) and dynamic charge acceptance (DCA) values can be achieved.

If the li-ion store has a high charge acceptance, and thus a high power uptake at its disposal, the duty ratio starting from 0.8 is to be regulated to a higher value by way of the machine control unit in order to maintain the target charging voltage of 60V on the li-ion store, with the voltage of the AGM battery decreasing at the same time.

If the Li-ion store has a high charge acceptance and hence a high input power, the duty factor starting at 0.8 must be set to a higher value via the engine control device in order to maintain the nominal charge voltage of 60 V at the Li-ion store as the voltage of the AGM battery drops at the same time.

In a second case, “closing” the controllable resistor 48 to an average resistance is effective such that a charge acceptance of the first capacitance 43 is at least reduced, and that more charge flows into the second capacitance 46 as in the case where the controllable resistor has the high resistance, which means in the first case.

By controlling the resistor when the input voltage has become higher than the input voltage set value, it is achieved that the charge acceptance of the first capacitor is reduced due to the supply voltage and due to the possibly present voltage peak in the supply voltage, so that more charge flows into the second capacitance than in the case where the controllable resistor had a high resistance.

In the extreme case, this catalyst layer not only accelerates the partial reaction, but carries out the entire electrode partial reaction with the associated charge acceptance or release, similarly to what has been described above with respect to the gas electrode, and the liquid active material accepts the partial reaction product (from the particles from the electrolyte).

Replacing the active material of the negative plate by a lead-carbon composite potentially reduces sulfation and improves charge acceptance of the negative plate.

Different types and specifications of the battery technical requirements are not the same, usually for testing the technical indicators are rated capacity or storage capacity, different rates of discharge performance, low temperature discharge performance, charge acceptance, resistance to discharge capacity, charge retention, electrolyte Storage capacity, overcharge endurance, safety performance, sealing performance, cycle life and so on.

The unique acid circulator is a VARTA benchmark technology that guarantees better acid circulation and keeps charge acceptance at the highest levels.

Shops should display any cash handling charges for accepting euro payments separately.

Until reaching a cell potential of 4.3 volts, the charge accepted amounted to 23.2 mAh.

All credit cards are accepted for payment of rental charges accepted.

And you pay no extra charges for accepting this payment.

All credit cards accepted for payment of rental charges accepted.

Their good charging acceptance makes them suitable or load profiles with large dynamics.